电动执行机构与阀体的安装
Installation of electronic executive body and body of valve
电动执行机构与阀体的安装(图5)指正指SHUT处(全闭位置
1.手动转动阀门,检查无异常情况,并使使阀门处于全闭位置。
Rotate the valve manually and make sure have unusnalsituation to check and make the valve in a completely closing position.
2.将支架固定在阀门上。 详情联系王经理:153,8032,9557(wei 信同号)
Fix the support on valve
3.将联轴器的一端套在阀门芯轴上
Suit an the valve core axle one end of shaft couping
4.用手柄驱动电动执行机构至全闭位置(指针正指SHUT处零开度刻度线处),将输出轴插入联轴器四方孔内。
Urge electronic executive body to close position(indicator
mean with handle shut zero tum on one degree of scale marks)all, insert the output shaft hen shaft coupling all sides in the hole
5.坚固支架与电动执行机构和阀体间的连接螺栓。
Connection bolt among firm support and electronic executive body and bod of valve
6.用手柄转动执行机构,确认运行平稳、无偏心、无歪斜、检查阀门在执行机构开度计指示范围能否实现全闭和全开
Potete the executive body with the handle, partial, does not have and crooked that confirm operating steadily, Not having check valve turn on degree count, instruct the range will you please realize, close and tum on all in executive
注意:用力不可过猛,否则会导致执行机构超程运行而造成损坏。
Attention: t exerts oneself to be can t too quickly, otherwise, it wil lead to the fact executive body exceed body Cheng run and cause the damage
(图5)电动阀门安装示意图
特别提示
对于自备支架、联轴器的用户,请注意:
For the users who providing the support, shaft coupling by oneself. please note
支架、联轴器应由专业机械技术人员设计加工并应符合
(图6)的标注要求。详情联系王经理:153,8032,9557(wei 信同号)
平行度不超过05m
Support, shaft coupling should be designed by the professional mechanical technical staff to process the requirement to marking that should also accord With( Fig. 6).n
联轴器两端轴孔的加工应保证必要的精度,尽可能消除转动间隙,以免阀门工作中出现回差
The processing of the both ends shaft hole of the sheft couping should guarantee the essential precision, dispel the interval of transmission as much as possible, in case that the difference that the appearance goes back in the valve wo
应严格保证联轴器两端轴孔的位置度,否则有可能超出执行机构设计的工作范围,导致因执行机构行程无法调整而使阀门C0再轴度不过中0.2mn不能正常工作
Should guarantee position degree of the both ends shaft hole of the shaft
(图6
coupingstrictly, otherwiseprobably beyond the scope of job which the executive body designs, lead to the fact that makes the valve unable to work normall because the joumey of executive body is unable to adjust.
【商家简介】 扬州瑞浦执行器制造有限公司主要经营:执行器、仪器仪表、电动阀门、机电成套设备、环保设备以及流体控制设备研发、生产、销售、安装和维修。(依法须经批准的项目,经相关部门批准后方可开展经营活动)等产品。公司尊崇踏实、拼搏、责任的企业精神,并以诚信、共赢、开创经营理念,创造良好的企业环境,以全新的管理模式,完善的技术,周到的服务,卓越的品质为生存根本,我们始终坚持用户至上 用心服务于客户,坚持用自己的服务去打动客户。...- 下一产品:任丘夹黄骅夹层锅 可倾式夹层锅卤肉专用
- 上一产品:任丘夹层锅煮凉粉用_沧州搅拌式夹层锅